IBM Personal Computer 9308 Manuel d'utilisateur Page 23
- Page / 244
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Removing rear filler panels: Use the following procedure to remove the rear filler
panels from the rack cabinet:
1. Grasp the rear filler panel firmly and slide it slowly toward the front of the rack
cabinet.
2. Lift the filler panel and remove it from the rack cabinet.
3. Repeat this procedure to remove both filler panels.
Installing rear filler panels: Use the following procedure to install the rear filler
panels on the rack cabinet:
1. Align the bottom of the rear filler panel with the tab on the bottom rear of the
rack cabinet.
2. Hold the filler panel fully against the side of the rack cabinet; then, slide the filler
panel toward the rear of the rack cabinet. Ensure that both the top and bottom
tabs are engaged by the filler panel.
3. Repeat this procedure to install both filler panels.
Removing and installing NetBAY42 panels
The primary NetBAY42 Rack cabinet comes with side panels installed. Remove the
side panels from a primary rack cabinet, or the outermost rack cabinets in a suite,
before you install or remove optional devices.
Rear filler panel
Figure 9. Removing the NetBAY25 rear filler panels
Type 9306 Model 250/420/421 13
- IBMPCServer/EnterpriseRacks 1
- Types 9306, 9308 1
- Contents 5
- Contents v 7
- About this manual 9
- General Checkout 11
- Power checkout 12
- Powering off the rack 13
- Type 9306 Model 250/420/421 15
- Installing a rack cabinet 16
- Type 9306 Model 250/420/421 7 17
- Type 9306 Model 250/420/421 9 19
- Front stabilizer bracket 21
- Rear filler panel 23
- Side panel 24
- Rear locking bar 24
- Door latches 26
- Attachment 32
- Bolt and nut 32
- Managing cables 33
- Cable-management brackets 34
- Part Listing (Type 9306) 38
- Locked Unlocked 41
- Perforated Doors (model 910) 45
- Locations 51
- Server selector console 51
- Server selector unit 52
- Connections 53
- Power distribution unit 53
- Cooling fan 54
- Sliding trays 55
- Sliding rails 56
- 4SB, 42S, 42E) 65
- Primary Rack (Model 42P) 66
- Extension Rack (Model 42X) 67
- Primary Rack (42S) 68
- Side panel locking bar 70
- Release latches 70
- Rear door 73
- Hinge pin 74
- Front door 74
- Front support bar 75
- > 18 kg ( 39.7 lb) 75
- Rear support bar 75
- Bolt and washer 77
- Threaded standoff 77
- Trim piece 77
- Statement 5 80
- CAUTION: 80
- NetBAY3 enclosure 83
- Foot pads 84
- Front cover 84
- Rear panel 85
- Device side rails 86
- Stacking NetBAY3 enclosures 86
- NetBAY3 enclosure 77 87
- Parts Listing (NetBAY3) 88
- NetBAY3E enclosure 89
- Stacking NetBAY3E enclosures 91
- Parts listing (NetBAY3E) 93
- © Copyright IBM Corp. 2001 85 95
- Cable tie 99
- Cable cover 100
- Cable clamp 101
- Front Rear 102
- Security screw 104
- Console switch 105
- Left-side bracket 105
- Right-side bracket 105
- Power supply 106
- Installing Optional Devices 111
- Installing cage nuts 114
- Clip Nuts 115
- Rear of rail 117
- Front of rail 117
- Power Distribution Unit 119
- Vertical mounting plate 120
- Cable-management bracket 120
- Blank filler panel 121
- Server handles 122
- Server rail screws 122
- Cable-management arm 122
- Server screws 123
- Rail adjustment 123
- Storage expansion unit 124
- Storage expansion unit screws 124
- Rail adjustment screws 124
- Filler panel 126
- Filler panel screws 126
- Shelf screws 126
- Rear of shelf 126
- Installing a fixed shelf 127
- > 45 kg (100 lb) 128
- Shelf bracket 128
- Keyboard 129
- Keyboard tray 129
- > 11 kg (24 lb) 129
- Rear screws 130
- Flat panel monitor 130
- Mounting studs 130
- IBM NetBAY Console Switch 131
- Features 133
- Tool requirements 134
- Specifications 134
- Installation overview 135
- Horizontal mounting bracket 138
- NetBAY (Console Switch) FRU 140
- 1x4 switch 06P6003 140
- 2x8 switch 06P6004 140
- Installing devices vertically 142
- Cabling your PDUs 147
- Rack PDU specifications 153
- Power cables 154
- Line cords 155
- Selector switch locations 180
- Tiered switch configuration 182
- Selector switch environment 183
- Resetting the selector switch 183
- Blank bezel 184
- Fixed shelf 184
- Starting the system 191
- Switching among servers 192
- Scanning the servers 193
- Saving Hardware Configuration 194
- Setting a scan pattern 194
- Changing menu attributes 196
- Related service information 201
- Safety inspection guide 239
- Grounding requirements 241
- Problem determination tips 241
- Part Number: 10K2658 244
- (1P) P/N: 10K2658 244
Produits connexes et manuels pour Boîtiers de commutation en série IBM Personal Computer 9308
(6 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels