Ibm All-in-One Super7 Single Board Computer PCM-5896 Manuel d'utilisateur Page 71
- Page / 128
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 3 Award BIOS Setup 59
Shadowing copies firmware from ROM into system RAM, where
the CPU can read it through the 16-bit or 32-bit DRAM bus.
Firmware not shadowed must be read by the system through the 8-
bit X-bus. Shadowing improves the performance of the system
BIOS and similar ROM firmware for expansion peripherals, but it
also reduces the amount of high memory (640 KB to 1 MB) avail-
able for loading device drivers, etc.
Enable shadowing into each section of memory separately. Many
system designers hardwire shadowing of the system BIOS and
eliminate a System BIOS Shadow option.
Video BIOS shadows into memory area C0000-C7FFF. The remain-
ing areas shown on the BIOS Features Setup screen may be
occupied by other expansion card firmware. If an expansion
peripheral in your system contains ROM-based firmware, you need
to know the address range the ROM occupies to shadow it into the
correct area of RAM.
- PCM-5896 1
- FCC STATEMENT 2
- Copyright Notice 3
- Acknowledgements 3
- A Message to the Customer 4
- Product Warranty 5
- Packing list 6
- Contents 8
- Information 13
- Features 15
- Specifications 16
- 6 PCM-5896 User Manual 18
- Board layout 19
- Board dimensions 20
- Installation 21
- Jumpers and connectors 22
- Connectors 23
- Locating jumpers 24
- Locating connectors 25
- Setting jumpers 26
- CPU installing and upgrading 27
- Installing DRAM (DIMMs) 28
- Clear CMOS (J2) 29
- DOC address select (J3) 30
- COM2 Select (J6, J11) 31
- LCD clock signal select (J7) 32
- (J10, J5) 33
- Audio output select (J12) 33
- S1 (2~6) CPU Vcore select 34
- S3 (1~3) CPU clock select 35
- S3 (4~6) CPU frequency ratio 36
- Power connectors (CN8, CN1) 37
- USB connector (CN3) 38
- Connecting the hard drive 39
- 40
- Front panel connector (CN6) 41
- IrDA connector (CN7) 42
- VGA display connector (CN12) 43
- LCD connector (CN9) 44
- CD Audio connector (CN10) 45
- Keyboard and mouse connector 45
- Audio connector (CN13) 46
- Parallel port IRQ 47
- 100Base-Tx Ethernet connector 48
- Serial ports (CN16) 49
- Floppy drive connector (CN17) 50
- Ethernet active signal LED 52
- Ethernet link signal LED 52
- DiskOnChip socket (U23) 53
- Award BIOS Setup 55
- Starting setup 56
- Setup keys 57
- Getting help 58
- Main setup Menu 59
- 48 PCM-5896 User Manual 60
- Standard CMOS setup 61
- Date and Time Configuration 62
- HARD DISKS 62
- 52 PCM-5896 User Manual 64
- •Base Memory 66
- •Extended Memory 67
- •Other Memory 67
- BIOS features setup 68
- Virus Warning 69
- Quick Power On Self Test 69
- Boot Sequence 69
- 58 PCM-5896 User Manual 70
- CHIPSET features setup 72
- Auto Configuration 73
- SDRAM CAS Latency Time 73
- Memory Hole at 15M-16M 73
- 62 PCM-5896 User Manual 74
- Power management setup 75
- DEFAULTS settings 76
- Standby Mode 78
- Suspend Mode 78
- PNP/PCI configuration setup 79
- PNP OS Installed 80
- Resources Controlled By 80
- Reset Configuration Data 80
- IRQ n Assigned to 80
- DMA n Assigned to 81
- PCI IRQ Activated by 81
- Load BIOS defaults 82
- Load setup defaults 83
- Integrated peripherals setup 84
- On-Chip Primary IDE 85
- IDE Primary Master/Slave UDMA 85
- IDE HDD Block Mode 85
- On-Chip USB controller 85
- Onboard FDC Controller 86
- Onboard UART Ports (1, 2) 86
- RxD, TxD Active 86
- ECP Mode Use DMA 86
- EPP Mode select 86
- ENTER PASSWORD: 88
- CONFIRM PASSWORD: 88
- IDE HDD auto detection 89
- Save & exit setup 90
- Exit without saving 91
- 80 PCM-5896 User Manual 92
- Flat Panel/CRT 93
- Controller Display 93
- Drivers and Utilities 93
- Software drivers 94
- Necessary prerequisites 95
- Before you begin 95
- Windows® 95 96
- Select Device window 98
- 88 PCM-5896 User Manual 100
- 90 PCM-5896 User Manual 102
- Windows® 3.1 104
- the system 106
- Windows® NT 3.51 107
- Windows® NT 4.0 108
- Ethernet Software 109
- Configuration 109
- 98 PCM-5896 User Manual 110
- Audio Setup 111
- Introduction 112
- Setting Up in Windows 95 112
- 102 PCM-5896 User Manual 114
- Setting Up in NT4.0 115
- 104 PCM-5896 User Manual 116
- Programming the 117
- Watchdog Timer 117
- 106 PCM-5896 User Manual 118
- Demo program 119
- 108 PCM-5896 User Manual 120
- Installing PC/104 121
- Installing PC/104 modules 122
- Female Male 123
- PC/104 ModuleMain board 123
- 112 PCM-5896 User Manual 124
- Optional Extras 125
- PCM-10489-4 Wiring Kit 126
- Optional USB Cable 127
- 116 PCM-5896 User Manual 128
Produits connexes et manuels pour Matériel Ibm All-in-One Super7 Single Board Computer PCM-5896
Matériel Ibm x Series 200 Manuel d'utilisateur
(152 pages)
(152 pages)
Matériel Ibm 48X-20X Manuel d'utilisateur
(50 pages)
(50 pages)
Matériel Ibm 8306 Manuel d'utilisateur
(314 pages)
(314 pages)
Matériel Ibm 71P7279 Manuel d'utilisateur
(128 pages)
(128 pages)
Matériel Ibm DS6000 Manuel d'utilisateur
(578 pages)
(578 pages)
Matériel Ibm 2 Manuel d'utilisateur
(72 pages)
(72 pages)
Matériel Ibm uPD78082 Manuel d'utilisateur
(274 pages)
(274 pages)
Matériel Ibm 22P6415 Manuel d'utilisateur
(62 pages)
(62 pages)
Matériel Ibm HOTS Manuel d'utilisateur
(13 pages)
(13 pages)
Matériel Ibm 20X Manuel d'utilisateur
(17 pages)
(17 pages)
Matériel Ibm RELEASE 7.3 Manuel d'utilisateur
(388 pages)
(388 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels