IBM THINKPAD 92P1836 Manuel d'utilisateur télécharger pdf

Part Number: 92P1836

Important

This publication contains product-specific parts

information for IBM ThinkPad Dock, ThinkPad Dock

II, ThinkPad Port Replicator, ThinkPad Mini Dock,

and ThinkPad Port Replicator II products.

This publication is intended for trained service

personnel who are familiar with ThinkPad products.

Before servicing an IBM ThinkPad products, be sure

to review the safety information on the hardware

maintenance manual of the ThinkPad computer.

FRU replacement notices

This section contains notices related to removing and

replacing parts. Read this section carefully before replacing

any FRU.

Screw notices

Loose screws can cause a reliability problem. In IBM

ThinkPad computer, this problem is addressed with special

nylon-coated screws that have the following characteristics:

v They maintain tight connections.

v They do not easily come loose, even with shock or

vibration.

v They are harder to tighten.

v They should be used only once.

Do the following when you service this machine:

v Keep the screw kit (for the P/N, see “Parts list” on

page 14) in your tool bag.

v Always use new screws.

v Use a torque screwdriver if you have one.

1 2 3 4 5 6 ... 15 16

Résumé du contenu

Page 1

Part Number: 92P1836ImportantThis publication contains product-specific partsinformation for IBM ThinkPad Dock, ThinkPad DockII, ThinkPad Port Replica

Page 2 - 90 degrees more

2010 ThinkPad Dock II PCI cover121(Bottom view)10

Page 3 - Removing and replacing a FRU

2020 ThinkPad Dock II top cover111(Rear view)Step Screw (quantity) Torque1 M2.5 × 4.8 mm (3) 0.392 Nm(4 kgfcm)2222Step Screw (quantity) Torque2 M2

Page 4 - 1010 ThinkPad Dock PCI cover

33(Bottom view)Step Screw (quantity) Torque3 M2.5 × 4.8 mm (6) 0.392 Nm(4 kgfcm)(continued)12

Page 5

Make sure that the system lock key A is set to theUnlock position. Release the front latches in step 4, andthen remove the top cover 5. Then det

Page 6 - 1020 ThinkPad Dock top cover

Parts listFRU P/N CRUIDThinkPad Dock 08N1546 NThinkPad Dock with extension plate 08N1537 NThinkPad Dock II 67P9010 *ThinkPad Mini Dock 67P9011 *ThinkP

Page 7

Power cords (ThinkPad Dock andThinkPad Dock II)IBM power cords for a specific country or region areusually available only in that country or region:Fo

Page 8

Power cords (ThinkPad Mini Dock)IBM power cords for a specific country or region areusually available only in that country or region:For 2-pin power c

Page 9

Tighten screws as follows:v Plastic to plasticTurn an additional 90 degrees after the screw headtouches the surface of the plastic part:90 degrees mor

Page 10 - (Bottom view)

Removing and replacing a FRUThis section presents directions and drawings for use inremoving and replacing a FRU. Be sure to observe thefollowing gene

Page 11 - (continued)

1010 ThinkPad Dock PCI coverBefore replacing the PCI cover:There are two types of ThinkPad Dock, as follows:v ThinkPad Dock: FRU no. 08N1546 (PCI cove

Page 12

Note: The following illustration shows how to remove thePCI cover of ThinkPad Dock (FRU no. 08N1546).Do the same to remove the PCI cover of ThinkPadDo

Page 13

1020 ThinkPad Dock top coverNoteThis section is only for the ThinkPad Dock (FRU no.08N1546). The top cover and screw kit for ThinkPadDock (FRU no. 12P

Page 14 - Optional FRUs

222(Bottom view)Step Screw (quantity) Torque2 M2.5 × 4.8 mm (8) 0.392 Nm(4 kgfcm)(continued)7

Page 15 - ThinkPad Dock II)

Make sure that the system lock key A is set to the Unlockposition. Release the front latches in step 3, and thenremove the top cover 4. For step 

Page 16 - For 3-pin power cords:

v Make sure that the device release lever is seatedcorrectly.v Make sure that the release button works correctly.9