IBM Car Amplifier 7220 Manuel d'utilisateur Page 147
- Page / 155
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Default Settings
Appendix F
F-1
Default Setting Function
The default setting function sets the model 7220’s controls and output displays as
follows:-
Left-hand LCD
Displays the AC Gain control on the upper line and the full-scale sensitivity control
on the lower line.
Right-hand LCD
Displays the magnitude as a percentage of full-scale output on the left-hand side and
the phase angle in degrees output on the right-hand side.
The ten controls accessed via the left-hand LCD are set to the following values:-
Full-scale sensitivity 500 mV
AC Gain 0 dB
Time constant 100 ms
Slope 12 dB/octave
Oscillator frequency 1000.000 Hz
Oscillator amplitude 0.500 mV rms
DAC1 output 0.000 V
DAC2 output 0.000 V
Output offsets OFF
Phase 0.00°
The two output offset controls accessed via the right-hand LCD are set as follows:-
X channel output offset 0.00 %
Y channel output offset 0.00 %
The remaining instrument controls, accessed via the setup menus, are set as follows:-
Input mode Single-ended voltage mode, A input connector
Coupling AC
Input connector shell Floating
Input device FET
Reference mode Internal
Reference harmonic 1st
Demodulator monitor Off
Output expansion Off
CH1 analog output X %
CH2 analog output Y %
- Model 7220 1
- FCC Notice 2
- Declaration of Conformity 2
- Table of Contents 3
- TABLE OF CONTENTS 4
- Appendix A, Specifications 6
- Introduction 9
- Chapter 1, INTRODUCTION 10
- Installation & 13
- Initial Checks 13
- 2.2 Initial Checks 15
- Technical Description 17
- 3.2.02 Signal-Channel Inputs 18
- 3.2.04 AC Gain 20
- 3.2.05 Anti-Aliasing Filter 20
- 3.2.07 Reference Channel DSP 22
- 3.2.08 Internal Oscillator 23
- 3.2.09 Demodulator DSP 23
- 3.3 Accuracy 24
- 3.5 Dynamic Reserve 25
- 3.8 Output Channel Filters 27
- 3.10 Noise Measurements 30
- 3.11 Power-up Defaults 30
- 3.12 Auto Functions 30
- 3.12.02 Auto-Sensitivity 31
- 3.12.03 Auto-Phase 31
- 3.12.04 Auto-Offset 31
- 3.12.05 Auto-Measure 32
- 3.12.06 Default Setting 32
- Front and Rear Panels 33
- 4.1.03 REF IN Connector 34
- 4.1.05 MENU Key 36
- 4.1.06 90º Key 37
- 4.1.07 SET Key 37
- 4.2 Rear Panel 38
- 4.2.11 CH1, CH2 Connectors 40
- 4.2.12 TRIG Connector 40
- 4.2.13 ADC1, ADC2 Connectors 40
- 4.2.14 DAC1, DAC2 Connectors 40
- Front Panel Operation 41
- 5.2.01 Input Setup Menu 42
- 5.2.02 Reference Setup Menu 44
- 5.2.03 Output Setup Menu 45
- 5.2.04 Control Options Menu 48
- AUTOMATIC 49
- EXTERNAL 50
- Contrast 50
- 5.2.06 RS232 Setup 1 Menu 51
- 5.2.07 RS232 Setup 2 Menu 52
- 5.2.08 RS232 Setup 3 Menu 53
- 5.2.09 GPIB Setup 1 Menu 54
- 5.2.10 GPIB Setup 2 Menu 55
- 5.2.12 Control Setup Menu 57
- 5.3 Auto Functions Menu 58
- AUTO OFFSET 59
- AUTO MEASURE 59
- Figure 5-18, AC Gain Control 62
- Figure 5-37, Ratio Output 72
- Figure 5-38, Log Ratio Output 72
- ADC1 Volts 73
- ADC2 Volts 73
- Computer Operation 77
- 6.3 RS232 and GPIB Operation 78
- 6.3.03 Choice of Baud Rate 79
- 6.3.08 Handshaking and Echoes 81
- 6.3.09 Terminators 82
- 6.3.10 Command Format 82
- 6.3.11 Delimiters 83
- 6.3.12 Compound Commands 83
- 6.3.14 Service Requests 85
- 6.4 Command Descriptions 86
- 6.4.02 Reference Channel 89
- 6.4.05 Instrument Outputs 92
- 6.4.06 Internal Oscillator 95
- 6.4.07 Auxiliary Outputs 96
- 6.4.08 Auxiliary Inputs 97
- Chapter 6, COMPUTER OPERATION 100
- 6.5 Programming Examples 106
- 6.5.05 Transient Recorder 108
- Storage and Frequency Sweep 109
- Specifications 111
- Reference Channel 112
- Oscillator 113
- Auxiliary Inputs 114
- Data Storage 115
- Interfaces 115
- Power Requirements 115
- Appendix A, SPECIFICATIONS 116
- B.1 RS232 Connector Pinout 117
- Appendix B, PINOUTS 118
- Demonstration 119
- Programs 119
- Cable Diagrams 123
- Appendix D, CABLE DIAGRAMS 124
- Alphabetical Listing of 125
- Commands 125
- 16,000,000 126
- ((25 × n) + 157) 126
- ((25 × n) + 1031) 126
- The value of n 144
- 1 Enables offset facility 144
- Default Settings 147
- Appendix F, DEFAULT SETTINGS 148
- Operating environment 2-1 151
- X[.] command 6-16, E-20 153
- Y[.] command 6-16, E-20 153
- WARRANTY 155
© 2020, manymanuals.fr. Tous droits réservés | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels